Instructions for Use

Before installation, ensure that the selected surface is clean, flat, and suitable for suction mounting. Check that all product components are complete. Proper installation is essential to achieve optimal suction performance and stability. Please follow the steps below carefully.

Step 1 — Clean Surface

Thoroughly clean the installation area to remove any dust, grease, or moisture, and ensure the surface is completely dry. Any residue or dampness may affect the suction performance.

Step 2 — Prepare Product

Assemble all necessary accessories and remove the protective cover from the suction cup. Make sure the suction surface is clean and free from any debris to ensure proper contact with the installation surface.

Assemble accessories and remove the cover

Step 3 — Position & Force Alignment

Place the suction cup onto the desired position. During installation, align the pressure point of your palm vertically with your shoulder so that your arm forms a straight line toward the wall. This allows you to apply body weight effectively, ensuring stronger pressure and helping the suction cup fully expel internal air for better adhesion.

Align palm pressure point vertically with shoulder

Step 4 — Apply Pressure

Use firm and steady force to press the suction cup tightly against the surface. Ensure full contact between the suction cup and the wall, and apply sufficient pressure to remove as much air as possible from the suction area.

Step 5 — Check Suction State

After pressing, check whether the suction cup is in a properly expanded and secured state. If the suction cup is not fully expanded or does not adhere properly, remove the product and reinstall it following the steps above.

Step 6 — Test Stability

After installation, press down on the hook to test stability. Ensure the product is firmly attached before placing any load on it.

To ensure proper performance, verify the suction state after installation. If any instability or loosening is observed during use, remove the product and reinstall it to maintain safe and reliable performance.

Line / Trace Series Installation

Before installation, ensure that the selected surface is clean, flat, dry, and suitable for suction mounting. Check that all product parts are complete, including the suction base, shelf body, hooks, and related accessories. Proper installation is essential for stable use. Please follow the steps below carefully.

Step 1 — Clean Surface

Thoroughly clean the installation area to remove dust, grease, water, or any surface residue. Keep the wall completely dry before installation, as moisture or dirt may affect suction performance.

Step 2 — Prepare Product

Assemble the product accessories as required and remove the protective cover from the suction cup. Make sure the suction surface is clean and free from debris before attaching it to the wall.

Prepare the product and remove the cover

Step 3 — Position & Apply Pressure

Place the suction base onto the desired position on the wall. Use either the palm of your hand or both thumbs to apply force, pressing the suction cup firmly and directly against the wall. Concentrating pressure at the center helps expel internal air and improves suction performance.

Use palm or thumbs to strongly press the suction cup

Step 4 — Check Pressing State

Check whether the suction cup is fully pressed and properly seated. The suction base should be fully compressed against the wall. If it remains un-pressed or there is a visible gap, press again or remove the product and reinstall it.

Check un-pressed and fully pressed suction state

Step 5 — Install Shelf Accessory

Attach the shelf body or hook accessory to the installed suction base according to the product structure. Slide or press the accessory into position and make sure it is properly fitted before use.

Install the shelf accessory onto the suction base

To maintain stable performance, check the suction state after installation and during regular use. If any loosening or instability is observed, remove the product and reinstall it before continuing use.

Bathroom Mirror Installation

Before installation, check that all product parts are complete, including the mirror, suction cup, connector, and shaving hook. Make sure the selected installation surface is clean, flat, dry, and suitable for suction mounting. Proper installation is required to ensure stable adhesion and secure use. Please follow the steps below carefully.

Step 1 — Attach the Connector

Press the connector upward into the bottom of the mirror until it is properly fitted. Ensure the connector is securely attached before proceeding to the next step.

Attach the connector to the bottom of the mirror

Step 2 — Install the Shaving Hook

Buckle the shaving hook onto the connector. Make sure the hook is correctly aligned and firmly attached to the connector.

Install the shaving hook onto the connector

Step 3 — Clean Surface

Clean the wall thoroughly and keep it completely dry. Remove any dust, grease, water, or surface residue before installation, as moisture or dirt may affect suction performance.

Step 4 — Remove Suction Cup Cover

Remove the protective cover from the suction cup. Before attaching it to the wall, ensure the suction surface is clean and free from debris.

Step 5 — Position & Force Alignment

Place the mirror onto the desired position on the wall. Align the pressure point of your palm vertically with your shoulder so that your arm forms a straight force line toward the wall. This helps apply pressure more effectively during installation.

Step 6 — Apply Strong Pressure

Use your body strength to strongly press the suction cup onto the wall. Use both hands if needed to ensure enough pressure is applied and the suction cup fully contacts the wall surface.

Step 7 — Test Stability

After installation, pull down the mirror for inspection to ensure it is fully adhered and securely immobile. Do not use the mirror until it has passed the stability check.

Step 8 — Remove Mirror Protective Film

Tear off the protective film from the mirror surface after the mirror has been securely installed.

Remove the protective film from the mirror

To maintain stable performance, check the suction state after installation and during regular use. If the mirror becomes loose or unstable, remove it and reinstall it following the steps above.

Falling Off

If the suction cup falls off or does not stay attached, please check the installation surface, suction cup condition, and installation method first. Suction products rely on a sealed vacuum environment. Any air leakage caused by wall gaps, grout lines, dirt, moisture, or insufficient pressure may affect adhesion.

Installation Precautions

Ensure the wall is clean and completely dry before installation.
Ensure the suction cup surface is clean and free from any gunk, dust, oil, or residue.
Avoid installing over grout lines, wall gaps, seams, textured areas, or uneven surfaces.
If the product is used in winter or in a cold environment, take the suction cup out of the box and leave it at room temperature for about 30 minutes before installation.
Install only on smooth, flat, non-porous surfaces such as ceramic tile, glass, mirror, stainless steel, acrylic, plastic, or laminate.
Press the suction cup firmly during installation to expel air and create a sealed vacuum.

Troubleshooting Test

For troubleshooting, please test the suction cup on a glass wall or mirror first.

Test Results

If the suction cup attaches firmly on glass or a mirror, the suction cup itself is functional. The original wall may be porous, uneven, have grout lines, or may not allow a proper vacuum seal.
If the suction cup still falls off on glass or a mirror, clean the suction cup with warm water, dry it completely with air or a hairdryer, and try reinstalling it again.
If it still cannot attach after cleaning and drying, please contact us for support.

What You Can Do

Remove the product from the wall.
Clean both the wall and the suction cup surface thoroughly.
Make sure both surfaces are completely dry before reinstalling.
Choose a smooth, flat, non-porous surface and avoid grout lines or gaps.
Press the suction cup firmly using your palm or both thumbs until it is fully attached.
Check the stability before placing any load on the product.

If possible, please provide photos of the wall surface and the suction cup surface when contacting support. This helps us confirm whether the issue is related to the installation surface, installation method, or the suction cup itself.

Coming Apart

If the product parts become loose or come apart during use, it is usually related to connection stability, assembly, or external impact. Please follow the steps below to check and resolve the issue.

Installation Check

Ensure all components are properly assembled before installation.
Make sure the connector is fully inserted and aligned correctly.
Check that all parts are securely fitted into place before use.
Do not force assembly if parts do not align naturally.
After installation, test stability before placing any load on the product.

Possible Causes

Components were not fully secured during assembly
The connector or accessory is not properly fitted
The product may have been impacted during shipping or handling
Repeated installation or removal may loosen connection points
Parts are not aligned correctly during installation

Troubleshooting

Please follow the steps below to identify the issue:

Check Results

If the product can be reassembled and stays secure → the issue was caused by improper assembly or loose connection.
If the product repeatedly comes apart after correct installation → the connection may not be holding properly.
If any part is cracked, broken, or missing → the product may have been damaged.

What You Can Do

Disassemble and reassemble the product following the instructions.
Ensure all connection points are fully secured and aligned.
Check for any visible damage before reinstalling.
Test the structure stability before normal use.

If the issue persists, please provide photos of the product, especially the connection area or damaged part. This will help our support team identify the issue and provide a suitable solution.

Removal & Reuse

Suction products can be removed and reused when handled properly. Please follow the steps below to remove the product safely, clean the suction cup, and prepare it for reuse.

Instructions for Reuse

Use a credit card or a similar thin, flat object to gently release the edge of the suction cup and remove the product from the wall. Do not pull the product forcefully, as this may damage the suction cup or connected parts.
Scrub the suction cup to remove any gunk, dust, oil, or residue. After cleaning, blow dry or air dry the suction cup completely before reinstalling or storing it for reuse.

Before Reinstalling

Make sure the suction cup surface is clean and free from residue.
Make sure the suction cup is completely dry before reuse.
Clean and dry the wall surface before reinstalling.
Reinstall only on a smooth, flat, non-porous surface.

For best results, do not reinstall the suction cup while it is wet or dirty. Moisture, dust, oil, or residue may prevent the suction cup from forming a sealed vacuum and may reduce stability.

Usage & Safety

For best performance, install the product only on smooth, flat, and non-porous surfaces.
Do not install on grout lines, uneven surfaces, textured walls, or porous materials.
This product relies on vacuum suction and is not a permanent mounting solution.
Always press firmly during installation and ensure full contact with the wall.
After installation, test stability before placing any items on the product.
Do not exceed the recommended load or apply sudden force or impact.
Check the product regularly to ensure it remains securely attached.
If any loosening or instability is observed, remove and reinstall the product.

Proper installation and suitable surface selection are essential for safe use. Suction performance may vary depending on wall conditions and installation method.

Surface Compatibility

Suction products require a smooth, clean, dry, and non-porous surface to create a sealed vacuum. Please check the surface type before installation.

Suitable Surfaces

Smooth ceramic tile
Mirror
Smooth glass wall
Stainless steel
Smooth PVC
Acrylic

Unsuitable Surfaces

Wood, lime wall, natural stone, or other porous surfaces
Dusty, wet, greasy, or dirty surfaces
Mosaic tile, grout lines, gaps, or uneven areas
Painted walls, textured walls, curved surfaces, or frosted glass

If the suction cup attaches firmly on glass or a mirror but falls off on the original wall, the original surface may be unsuitable for suction mounting.

Installation Instructions

Step 1 Clean the wall and keep it completely dry before installation.

Step 2 Remove the protective cover from the suction disc before installation.

Step 3 Press the suction disc firmly for at least 5 seconds, then press along the edges to remove air completely.

Step 4 Press the vacuum button to activate suction and secure the grab bar.

Step 5 Check stability by pressing down on the grab bar after installation.

Proper installation is essential for optimal suction performance. If the grab bar feels loose or unstable, remove it and reinstall it before use.

Installation Instructions

Step 1 Assemble the suction cups and grab bar together, then remove the protective cover from the suction pad.

Step 2 - Clean wall and avoid grout lines

Step 2 Clean the wall and keep it completely dry. Do not install the suction cup on thin seams, grout lines, or uneven areas.

Step 3 Place the shower grab bar in the desired spot for installation. Make sure both suction cups are positioned on a smooth and flat surface.

Step 4 Press the pad firmly for 5 seconds, then lock the latches securely.

Step 5 Ensure the suction cup is firmly pressed against the wall, leaving no gaps between the panel and the suction pad.

Step 6 Grab the shower bar and give it a firm shake. A successful installation should remain steady and secure.

Proper installation is essential for suction performance. If the grab bar feels loose, moves, or does not remain firmly attached after testing, remove it and reinstall it before use.

Troubleshooting Tips

1. Check the wall for suitability, defects, and cleanliness.

2. Check suction cups for dirt and installation in place.

If any of the above problems occur,
try the following solutions:

1 Change the installation position if the wall is cracked or unsuitable.

2 Clean the wall.

3 Clean suction cups with water and dry them using a hair dryer.

4 Reinstall suction cups if not properly placed.

5 If the suction cups are defective, please contact us at customerservice@tailigo.com.

If installed in a bathroom, will the suction cup be stable in a damp environment?

Ensure that the wall is clean and dry during installation, with no water ingress. It can be used in a humid environment all year round.

If problems occur during installation, how can I quickly determine whether the problem is with the product or the wall surface?

Ensure that the suction cups are clean and dry, then install the grab bar on a smooth, clean, and dry glass surface. If the grab bar can be installed well on the glass, this means the original wall is not suitable for the suction cups. If the grab bar does not work on the glass, please contact us.

Usage & Safety

Before Use

Always check that the grab bar is firmly attached before each use.
Make sure both suction cups are fully secured and there are no visible gaps.
If the grab bar moves, loosens, or feels unstable, remove it and reinstall before use.

Proper Use

Use the grab bar only as an assistance handle for balance and support.
Do not use it as a permanent safety rail or full body-weight support device.
Avoid sudden pulling, impact, or excessive force during use.
Do not exceed the recommended weight limit stated for the product.

Surface & Environment

Use only on smooth, flat, clean, dry, and non-porous surfaces.
Do not install on grout lines, seams, textured walls, painted walls, or uneven surfaces.
Keep the installation area clean and dry during installation.
If used in a humid bathroom environment, check suction stability regularly.

Regular Check

Check the grab bar before each use.
Reinstall immediately if any loosening, movement, or air leakage is observed.
Clean the suction cups and wall surface periodically to maintain suction performance.

Important: Suction grab bars rely on a sealed vacuum environment. Wall condition, installation method, moisture, and repeated use may affect suction performance. Always test stability before use.

Please select a page for this panel in the theme editor.

Surface Compatibility

Suction products require a smooth, clean, dry, and non-porous surface to create a sealed vacuum. Please check the surface type before installation.

Suitable Surfaces

Smooth ceramic tile
Mirror
Smooth glass wall
Stainless steel
Smooth PVC
Acrylic

Unsuitable Surfaces

Wood, lime wall, natural stone, or other porous surfaces
Dusty, wet, greasy, or dirty surfaces
Mosaic tile, grout lines, gaps, or uneven areas
Painted walls, textured walls, curved surfaces, or frosted glass

If the suction cup attaches firmly on glass or a mirror but falls off on the original wall, the original surface may be unsuitable for suction mounting.

Instructions for Use

Before storage, ensure that all items are completely dry, clean, and neatly folded. Check that the storage bag is undamaged, the zipper is aligned properly, and the air valve is functioning correctly. Proper packing and sealing are essential to achieve maximum compression, protect stored items, and maintain long-term storage performance. Please follow the steps below carefully.

1 Step 1 — Pack Items

Place your folded clothes, bedding, or soft household items neatly inside the storage bag. Ensure that the contents do not overfill the bag and leave at least a couple of inches of space between the packed items and the zipper edge. This extra space is necessary to ensure proper sealing and prevent zipper stress.

Leave space from the zipper

2 Step 2 — Zip and Rotate

Firmly slide the sealing clip along the zipper multiple times to ensure the zipper is fully sealed from end to end. After sealing, rotate the air valve to the left to open it and prepare the bag for vacuum air extraction.

Slide the clip and open the valve

3 Step 3 — Vacuum

Use a standard household vacuum cleaner to remove the air from the bag. Hold the vacuum nozzle tightly against the valve opening to maximize suction efficiency. Continue vacuuming until the bag reaches the desired compression level.

Vacuum out the air

4 Step 4 — Rotate and Store

Once the air has been fully removed, rotate the valve to the right to close and seal it tightly. Store the compressed bag in your closet, under your bed, or in any storage space where space-saving organization is needed.

Close the valve and store the bag

For best long-term storage results, avoid storing sharp objects, damp items, or overfilled contents inside the bag. Periodically check the seal and valve to ensure compression is maintained.

Troubleshooting

If the vacuum bag leaks air, loses compression, or fails to stay compressed, please follow this systematic guide to identify and resolve the issue. Vacuum storage bags rely on a completely sealed environment. Any air leakage caused by zipper gaps, valve issues, dirt, moisture, or improper packing may affect performance.

Initial Check: Air Leakage & Compression Failure

Check whether the zipper sealing strips are clean and free from dust, hair, lint, or debris.
Check whether the air valve is fully closed after vacuuming.
Inspect the valve area for dust, loose fit, or sealing obstruction.
Ensure bulky or non-breathable items are not directly blocking the air valve from inside the bag.
Check whether the bag is overfilled, which may create zipper strain or incomplete sealing.

Installation & Sealing Precautions

Before sealing, ensure the zipper strips (“bone strips”) are completely clean.
In cold weather, allow the bag to rest at room temperature for approximately 30 minutes before sealing.
Leave 5–10 cm of space between packed items and the zipper edge.
Use the sealing clip and slide firmly along the zipper 2–3 times to ensure a complete seal.
After vacuuming, rotate the valve tightly closed to prevent slow air leakage.

Troubleshooting Test

To confirm whether the issue is caused by sealing or a product defect, perform the following test:

The 24-Hour Flat Surface Test

Seal and vacuum the bag normally.
Place it on a flat, clean surface without moving it for 24 hours.

Analyzing Results

If the bag remains compressed → the original issue was likely caused by improper sealing, dust, or packing method.
If the bag gradually reinflates → clean the zipper and valve thoroughly, dry them completely, and test again.
If the bag still leaks after proper cleaning and resealing → the bag may require further support.

What You Can Do

Remove all stored items from the bag.
Inspect the bag for tears, punctures, or visible physical damage.
Clean the zipper strips and valve area thoroughly.
Ensure all surfaces are completely dry.
Repack items, leaving enough space from the zipper edge.
Seal the zipper firmly using the slider 2–3 times.
Vacuum again and close the valve tightly.

If the bag still fails to maintain compression after cleaning, drying, and resealing, please contact support. Providing photos of the zipper seal and valve area will help us determine whether the issue is related to sealing, usage, or product condition.

Warm Tips

Proper use and storage are essential to maximize bag performance, protect your stored items, and ensure long-term safety. Please review the following important safety reminders and storage guidelines carefully before use.

Safety

Keep storage bags away from babies and children at all times to avoid the risk of suffocation.
Never allow children to play with the bag, valve, zipper, or packaging materials.
Store unused bags safely out of reach of children.

Wrinkle Prevention

Do not vacuum all air out completely when storing delicate textiles.
Leaving a small amount of air inside the bag may help reduce excessive wrinkles or deep creasing.
For wrinkle-sensitive fabrics, avoid over-compression.

Storage Tips

Suitable for storing pillows, clothing, bedding, and general household textiles only.
Do NOT store food, liquids, leather goods, or sharp objects inside the bag.
Avoid storing items with poor breathability, such as certain leather products or tightly packed materials that may interfere with air extraction.
Do not directly pull the valve cap or zipper when moving or handling the bag.
Keep bags away from sharp objects or rough surfaces to prevent punctures or tears.
When properly sealed and free from leakage, the bag helps protect stored items from dust, moisture, insects, moths, and mildew for extended storage periods.
The storage bag is reusable multiple times when used according to the provided instructions.

Long-Term Protection

Periodically inspect the zipper seal and valve condition during long-term storage.
If air leakage occurs, reopen, inspect, reseal, and vacuum again.
For best protection, store the compressed bag in a cool, dry place away from excessive heat or sharp pressure.

Important Safety Warning

To avoid the danger of suffocation, keep this bag away from babies and children.

Vacuum Storage Bag Capacity Guide

The capacity below is for reference only. Actual storage capacity may vary depending on fabric thickness, folding method, item size, and compression level.

Flat Bags

Size Name	Dimensions	Recommended Items	Approx. Capacity
Jumbo	100 × 80 cm	Pillows	5–6 pcs
		Comforters / Quilts	2–3 pcs
		Plush Toys	3–5 pcs
		Down Jackets	5–6 pcs
		Regular Tops	7–10 pcs
		Pants	7–10 pairs
		Sheet Sets	3–4 sets
XXL Jumbo	120 × 100 cm	Pillows	8–10 pcs
		Comforters / Quilts	3–4 pcs
		Plush Toys	5–8 pcs
		Down Jackets	8–9 pcs
		Regular Tops	12–15 pcs
		Pants	12–15 pairs
		Sheet Sets	5–6 sets

Side-Gusset Bags

Size Name	Dimensions	Recommended Items	Approx. Capacity
Jumbo	100 × 70 cm	Pillows	3–4 pcs
		Comforters / Quilts	2–3 pcs
		Plush Toys	3–5 pcs
		Down Jackets	5–6 pcs
		Regular Tops	7–10 pcs
		Pants	7–10 pairs
		Sheet Sets	3–4 sets
XXL Jumbo	120 × 100 cm	Pillows	8–10 pcs
		Comforters / Quilts	3–4 pcs
		Plush Toys	5–8 pcs
		Down Jackets	8–9 pcs
		Regular Tops	12–15 pcs
		Pants	12–15 pairs
		Sheet Sets	5–6 sets
Large	80 × 60 cm	Pillows	1–2 pcs
		Comforters / Quilts	1 pc
		Plush Toys	2–3 pcs
		Down Jackets	4–6 pcs
		Regular Tops	5–7 pcs
		Pants	5–7 pairs
		Sheet Sets	2–3 sets

Cube / 3D Bags

Size Name	Dimensions	Best For	Recommended Items	Approx. Capacity
Jumbo	80 × 100 × 35 cm	Bedding	Pillows	4–6 pcs
			Comforters / Quilts	3–5 pcs
			Plush Toys	/
			Down Jackets	6–8 pcs
			Regular Tops	12–18 pcs
			Pants	10–15 pairs
			Sheet Sets	4–6 sets
Extra Large	70 × 100 × 46 cm	Clothing	Pillows	5–7 pcs
			Comforters / Quilts	3–4 pcs
			Plush Toys	4–8 medium pcs
			Down Jackets	8–10 pcs
			Regular Tops	18–25 pcs
			Pants	15–20 pairs
			Sheet Sets	3–5 sets

Tip: Avoid overfilling the bag. Leave enough space near the zipper to ensure a proper seal and better compression performance.

Before installation, ensure that the selected surface is clean, flat, and suitable for adhesive mounting. Check that all product components are complete. Proper installation is essential to achieve optimal adhesive performance and stability. Please follow the steps below carefully.

Step 1 — Prepare Adhesive

Take out the adhesive strip and remove the white protective liner. Ensure the adhesive surface remains clean and free from any debris before application.

Step 2 — Attach to Base

Apply the adhesive strip directly onto the mounting base and press firmly for 10 seconds. Ensure the strip is centered and makes full contact with the base surface.

Step 3 — Clean Surface

Thoroughly clean the installation area on the wall to remove any dust, grease, or moisture. Ensure the surface is completely dry, as any residue or dampness may significantly affect the adhesive's bonding strength.

Step 4 — Position & Apply Pressure

Align the base to your desired position on the wall. Press the base firmly against the wall, applying steady force from top to bottom, and hold for 30 seconds. Repeat this pressing action 3 times to ensure a secure and durable bond.

Step 5 — Complete Installation

Once the base is securely pressed, the installation is complete. Ensure the product is firmly attached before placing any load on it.

Step 6 — Important Notice

Please note that the adhesive strip is designed for one-time use and cannot be reused. If you need to relocate the product, you will need a new adhesive strip.

Warning: This product contains small parts and presents a choking hazard. It is not suitable for children under 3 years of age. Adult supervision is required during installation and use.

Before installation, ensure that the selected surface is clean, flat, and suitable for adhesive strips. Check that all product components are complete. Proper installation is essential to achieve optimal adhesive performance and weight-bearing stability. Please follow the steps below carefully.

Step 1 — Clean Surface

Thoroughly clean the installation area to remove any dust, grease, or moisture, and ensure the surface is completely dry. Any residue or dampness may severely affect the adhesive performance.

Step 2 — Prepare Product

Separate the individual strips (if applicable), then fasten them together in pairs by aligning and pressing them until you hear a click or feel them securely locked.

Step 3 — Attach to Frame

Tear off the liner from one side of the strips, attach them to the designated positions on the back of the frame, and press firmly to ensure full contact and a secure bond between the strips and the frame.

Step 4 — Position & Wall Alignment

Tear off the liners from the other side, and adjust the position and angle of the frame on the wall. Then, press the frame firmly against the wall to allow the strips to make initial contact with the surface.

Step 5 — Remove & Reinforce

Gently remove the frame from the wall (leaving one strip on the wall and its mate on the frame) to reinforce the adhesive. Press each strip left on the wall firmly from top to bottom for 30 seconds. Once done, wait 1 hour to allow the adhesive to fully cure and build maximum strength.

Step 6 — Reattach & Test

After waiting for 1 hour, align the strips on the frame with the strips on the wall, and press the frame firmly until each pair of strips is securely snapped and locked together. Ensure the product is firmly attached before regular use.

What to do if the product falls off: If the strips fail to hold, first verify that your surface is on the "Recommended" list above. If the surface is correct, ensure you allowed the full 1-hour cure time after initial application. Ensure you are not mounting on "non-stick" paint variants, which can feel smooth but reject adhesive bonds.

Proper Removal Technique:

Hook＆Loop:

Never pull the strip towards you.
Gently HOLD mounting base in place to prevent the base from snapping fingers.(DO NOT press down.)
STRETCH STIRPS SLOWLY AND LATERALLY until the base and strip RELEASE.
Remove the strip from hook and keep the surface clean.

Mashroom Head:

To remove the product without damaging your wall or frame:

Peel Gently: Carefully pull the frame away from the bottom to expose the adhesive strips.

Vertical Release: Place your finger on the top of the adhesive strip to hold it against the wall. Grasp the tab and pull the strip straight down vertically along the wall surface until the adhesive releases. Do not pull the strip outward (at an angle) toward you, as this may damage the paint.

Proper usage is vital for safety and surface protection. Please review these precautions before installation:

Safety Warning: Do not hang fragile items, precious souvenirs, or heavy objects that could cause injury or damage if they fall.

Placement Caution: Avoid mounting items above beds, seating areas, or in high-traffic spaces where a falling object could cause harm.

Latex Paint Care: * New Walls: If the wall has been recently painted with latex, wait at least one month to ensure the paint is fully cured and dry.

Old Walls: Inspect the wall for signs of aging or peeling. Do not use on walls where the paint is flaking or where dust/powder is falling off.

Preparation:

1.Ensure the back of the frame is flat and free of existing hardware or loose hanging pieces.

2.Clean the mounting surface thoroughly with a dry cloth to remove dust and oils.

For the best results, use this product only on smooth, flat, non-porous surfaces.

Recommended Surfaces:

Ceramic tile
Smooth wood
Latex painted walls (see notes below)
Acrylic panels
Metal panels
Smooth marble

Surfaces to Avoid (Not Suitable): This product will not adhere to surfaces with non-stick coatings, rough textures, or unstable finishes, including:

Rough grey walls, stucco, or cement walls
Wallcloth or wallpaper
Anti-fouling or "environmentally friendly" paints (often contain anti-stick additives)
Art paints or concave-convex surfaces (depth ≥ 0.2mm)
Waxed glass or tile surfaces

The Guardian Series 3.0 is a manufacturing breakthrough that utilizes novel needle-resistant material technology. It is recommended for use in the most dangerous situations that require the highest level of cut and needlestick puncture resistance.

Fit and Fastening: An elastic cuff with a hook-and-loop fastener provides the glove with a secure and comfortable fit.

Materials and Protection: 2 layers of SOMOR material (interior layer) provide excellent cut and needlestick resistance while being flexible enough to offer unsurpassed dexterity. The comfortable back-of-hand material makes it suitable for extended wear.

Important Safety Warning:

This product is cut and needle resistant but NOT CUT AND NEEDLE PROOF.

Do not use with moving or serrated blades or tools.

Product Usage

Our ultra-thin and lightweight needle-resistant gloves utilize a revolutionary "liquid armor" design to protect against needles, broken glass, sharp tools, and other hand-injury threats.

Advanced STF Technology: The palm is constructed with an HP composite layer and a SilKey composite layer, both integrated with our patented shear thickening fluid (STF) technology. The STF remains liquid to allow movement but instantly hardens upon encountering a needle poke.
Dexterity & Fit:
- The ultra-thin palm side (just 2.0mm thick) delivers unmatched tactile sensitivity and dexterity.
- The back of the gloves is made from an elastic fabric for easy maneuvering.
- An elastic wrist with a hook-and-loop closure ensures a secure, custom fit.
Protection Profile: Offers excellent hypodermic needle resistance, cut protection, and abrasion resistance.
Important Safety Warnings:
- This product is cut and needle resistant but NOT CUT AND NEEDLE PROOF.
- Do not use these gloves with moving or serrated blades or tools.

To maintain the integrity of the protective materials and prolong the lifespan of the gloves, please strictly adhere to the following cleaning tips:

Recommended Cleaning: Gently clean with a damp brush of fine bristles to remove dirt from the surface.

Prohibited: DON'T wash with water or use a washing machine, as this can damage the internal protective layers.

Troubleshooting & Legal Notices

Because this is specialized protective equipment, troubleshooting primarily involves usage limits and liability disclaimers:

Protection Failure / Wear and Tear:

If the gloves experience abnormal wear, tears, or punctures, stop using them immediately. Ensure you are not using them with moving or serrated blades or tools, as the product is not designed to protect against these hazards.

Liability Disclaimer:

TAILI will not be liable for any loss or damage arising from this product, whether direct, indirect, special, incidental, or consequential. Users must assess the product's suitability for their specific environment.

Product Verification:

This product is protected by patents and patents pending. Ensure you are purchasing through authorized channels to avoid counterfeit products lacking genuine protective capabilities.